2011年4月1日星期五

LED lighting over-current protection devices application points

Leds have low power consumption, long service life, environmental protection and other distinct characteristics, in size since childhood to the large size backlight application field after penetrated deep into panel backlighting now further to general lighting applications expansion, at present already in landscape, building, commercial, car, mobile lighting etc rapid development.
Facing many applications LED bulb lighting, because the market does not form a unified standards, exist multiple drive solutions, but million remain essentially among them, from the over-current protection perspective generally according to the led light body to the input current can be divided into: dc input and grid ac input two kinds of most basic types, two types of main difference between driving power have communication module. Turn dc Of course the market also has a lot of resistance, resistance to let step-down etc low cost solutions, no EMI rectifier and constant-current driver module, but because the primary end the fuse choose requirements and figure 2 is consistent, in this into a second type.

LED tube lighting over-current protection for the main purpose has 3:
First, the purpose of protecting the personal property safety, be in commonly power input voltage higher applications often for this purpose increase protection devices.
Second, with external system will subsystem, if external system partition appear instability will affect subsystems security; On the other hand inside the subsystem, such as parallel appear device damage appears short circuit failure modes, device or due to external factors lead to internal otherwise secure insulation class, resulting in destruction of internal circuit short-circuit, if not fuse action and outside system and not timely partition of effective measures, will cause the external system if the insurance system action which will cause the whole power supply system, and the continuous in important places such as hospitals and other indirect cause accidents loss, even may be causing casualties, so sometimes need in power input plus 2 fuse.
Third, the protection of important and valuable electronic components or devices. For the LED illumination lamps and lanterns speaking, LED lamp bead cost accounting for the entire lamps and lanterns, in the most of the cost of power drive or isolated not constant current driver circuit, need to drive an output terminal of the necessary over-current protection.
Because the power input structure is different, in selecting over-current protection device has the larger concerns distinction:
1, aimed at dc input type of DCin fuse choose, need special attention to fuse temperature reduction factor parameter, due to the fold of high power LED is relatively large, heat in LED spotlight lamp cup internal temperature is opposite taller, if choose temperature fold reduction larger fuse will choose current larger specifications, in the same job, current specifications big electric shed the fuse protection ability to reduce some relative; In addition DCin position, because back-end capactance filtering can use, can produce larger boot pulse current, so in the parts need to pay attention to choose fuse strict conditions and otherwise consider pulse is apt to cause the fuse was mistake options on the phenomenon, it is difficult to pass pulse thrust many times switch machine experiment and surge current experiment, in the recommended product ability strong resistance to pulse.
2, the fuse selection for driver output in note fuse temperature fold reduction factor at the same time, still need to consider the fuse fusing speed indicator, because here is, in a circuit current wave abnormal or component invalidation, need quick isolating circuit, protect the LED lights after, on the position of the recommended options fast break types and temperature decreases the fuse fold.
Above two occasions on common market have more choices, low-voltage fuse patch SolidMatrix AEM technology such as ® technology from the fuse, size 0402 to 1206, current specifications from 0.5 to 30A, have fast break, quick break, resisting high pulse, slow and breakage different series, different specifications, different characteristics of products for each engineer to choose.
3, and LED par light lighting for ac input ACin position, especially the spherical bulb LED the size of both need to consider the fuse, and the need to consider the fuse withstand voltage values. But the present market condition to withstand voltage range of fuse wide communication is larger, rarely general volume of small volume fuse a patch can be achieved, 250VAC compression value for this application fronts, AEM technology introduced AirMatrixTMAF2 series patch fuse, volume only 6.1 mm * 2.5 mm * 2.2 mm, shape petite but can withstand 250VAC voltage, but also has a high consistency, low resistance, high resistance to pulse ability, will bring you advantages such as new applications engineers friends experience.
Some engineers, no matter use friends think the fuse is negative, neutral firewire in in happened current can be broken, can protect. Here with you friends share experience, engineers have potentials needs with the fuse, use the lines in the ground can also cut off the circuit, fuse off the whole lighting appliances, after but still exist with the earth, once in place inside device erps short-circuit will cause circuit danger. So in some socket can reverse plugged in countries, such as Germany or China, from a security perspective, need to consider in some can reverse the LED illumination lamps inserted LN with best in the basement.

没有评论:

发表评论