3.1 radiation to come loose to influence coefficient of LED
Figure 2 exterior blackness for 0.8 for the temperature at which the image. According to Stephen boltzmann's law, irradiance j * and temperature T: the relationship between the search-evade antagonistic sigma T4 * = j. Among them the blackbody radiation coefficient for the search-evade antagonistic; Sigma = a x 10-8w / (m2 · k4), called Stephen boltzmann constant. Therefore, the higher the temperature is, that the irradiance. When the input power, for via surface radiation 1W leds scattered out for the heat 7.63 x 10 - total 4W, only the thermal power of 1.63 ‰; Power reached by radiation when 2W scattered out heat also accounted for only 6.33 ‰. So change to increase the cooling capacity coefficient of thermal radiation to come loose to improve have much effect, key enhances two other cooling pattern: the heat transfer and heat convection. Nonetheless, there are still some manufacturers will LED device outside surface of the painted black, in order to maximize the use of radiation heat.
3.2 thermal conductivity of the influence of heat to LED
Consider only heat conduction and convection, change different packaging filling materials such as silicone resin. To obtain the result, fig.03 shows. Even find a thermal conductivity 7Wm - as the earn - 1 epoxy resin component packaging materials, using thermal conductivity compared to 0.25 Wm - earn - 1 epoxy resin component packaging materials, chip temperature drop much, aluminum plate temperature decline was only 2.271 ℃, the maximum power only raised 0.69 W. In fact, thermal conductivity value over 7Wm - above, can earn - 1 the commercialization of transparent silicone resin packaging materials at present there is no literature reports. As shown in figure 4 shows distribution cloud.
Table 2 shows lens thermal conductivity 0.2 Wm - earn - 1, different heat sink to the thermal conductivity of materials of maximum power influence LED. From table 2 see, heat sink to the maximum heat material LED a little effect. Ability to
To sum up, the thermal conductivity of the most high power LED changes affect faint.
3.3 increase power dissipation area of effect of LED heat dissipation
Table 3 for 3 different thermal radiation on the temperature distribution, most LED high-power influence. Can see, increase power dissipation area is very good thermal radiation, can easily improve LED device heat capacity, which is currently LED display products have commonly used one of the cooling pattern. But the drawbacks is obvious: impact cost, increase products weight, influence package density. Indefinitely improve LED heat sink area clearly not reality, so use commonly 1.5 inch2 heat sink ascending LED display products maximum power to around 10W, due to the cost can continue to improve factors.
3.4 convection heat to the influence of LED way
Common convection radiator two different ways: natural convection and forced convection. Fixed structure of the heat dissipation and surface heat transfer coefficient relevant. Air cold way, different heat transfer coefficient of the influence of the most power as shown in figure 5 shows. Strong convective in certain speed way it will greatly improve LED light products within the heat capacity, helps to increase the cooling effect.
To sum up, whether increase power dissipation area or increase convection speed cannot unrestricted increase the cooling ability, its reason is: when the heat dissipation structure, way, even after fixation LED thermal conductivity has risen, can't really be drastically lower chip temperature; Facts prove increase power dissipation area, can promote heat dissipation. But because the cost limits, and impossible to increase heat area unrestricted, accordingly, want ascending LED display products are key to the heat capacity, in efforts to increase power dissipation area, looking for a can quickly will surface heat away cooling pattern.
4, endnotes
Using ANSYS software of high power LED display 3-d finite element thermal analysis, and painted by different factors influence the when the temperature of the device and through comparing the cloud of various factors on the influence of thermal performance, draw the conclusion: after the necessary material selection optimization, the pursuit of material thermal conductivity is cooling capacity to improve LED to modify details, want to greatly improve the LED cooling capacity, the key is to increase power dissipation area and cooling pattern change.
没有评论:
发表评论