2010年12月29日星期三

The LED display installed skills and matters need attention analysis

The led display installed skills and matters need attention analysis
, using hardware device list
The led display, signal connecting cables, power source jumper, system control card (loaded in computer inside), the system accepts charge card (loaded in led screen inside) and desktop computers (including DVI video output and serial port), display and related affiliate accessories.
Use process
Installed hardware
Installation procedure is as follows:
1, put on the mainboard DVI display adapters inserts installed card slot, AGP drivers,
2, put the data acquisition card at empty PCI slots (if used);
3, DVI cable with the data acquisition card with display card together,
4, the line with serial port (Rs232) connected (optional, spirit star rain system needs);
5, with cable connected with receiving card, According to the number (specific engineering drawings)
6, inspection connections can be set or correct on electrical commissioning.
Software installation
Installation procedure is as follows:
1, video card driver installation
Will display card driver disc insert cd-rom, can automatically enter installation state, please click hint operation can.
First installation DirectX8.1; Then install driver, Finally the setup control led panel.
2, played software
Install special play and large screen set software LED the studio, or other control software
With the screen attached application software CDS insert cd-rom, copy or installation of all the procedures to the computer.
Electronic screens operation procedure (important)
1, the tail: please turn on the computer and reopen the electronic screens.
For each device access to power (make sure the input voltage conform to product requirements)
Open the led sign bodies (screen body electricity a moment can have regional flashing, show screen body electricity), open the computer, make sure that video card correctly set (not correct will not show scenes, namely screen), open the control software, basic pixel size and display area Settings (this setup does not affect the led screen)
2, GuanBing: first off the led sign body, turn off the power control software, then right off the computer.
Found the problem
Check the connection mode is correct, including, specialized in part of the connection (elv part is in production enterprise test), signal connection are correct, mainly for receiving card system input and output direction correctly, receiving card has direction sighing.
System connection are correct (please consult the system connection specified)
Computer software part whether complete installation, including graphics Settings (please consult the graphics Settings specified) and control software installation.
note
1, abide by the user manual "in the operation step,
2, moistureproof, humidity requirement for: the maximum operating temperature, the led panel should be less than relative humidity for 92%
3, temperature is appropriate, temperature requirements for: work environment temperature - 20 ° C 80 ° C acuities t acuities
Storage environment temperature - 40 ° C 60 ° C acuities t acuities
4, the power supply should comply with the requirements
The led display screen of the power supply voltage: 220V + 10% frequency: 50HZ + 5%
Safety earth contact with neutral ground wire isolation reliable, reliable, into a power away from high-power electric equipment.
led tube electronic display screen, switch precautions:
1 switch order:
Tail: first after starting, the tail.
When GuanBing: first, GuanBing after shutdown
(first shut the computer business screen, can cause screen body appear high window, burned tubes, if the consequences are serious.
2, the interval time switch screen is greater than 5 minutes.
3, computer into engineering control software, and then the tail electrify.
4, avoided in all white screen condition, because the system of the tail impulse current largest.
5, avoid the runaway condition, because the system of the tail impulse current largest.
A computer is not into the control software program; etc.
B the computer is not electricity,
C control section power supply has been opened.
6. Environmental temperature exorbitant or the radiation condition is bad, should pay attention to not long tail.
7. Electronic display body part appear line are very bright, attention shall be paid to GuanBing in time to the state in shoulds not be long tail.
8. Often appear to display the power switch trip, should promptly monitor screen body or replace the power switch.
9. Regular inspection holds firmly hangs. If have, become loose phenomenon, pay attention to adjust, afresh reinforcement or update crane parts.
10. According to the big screen display screen body, the control part environment conditions, avoid worm shall, when necessary, place prevent rat poison.
Second, the control part of change, change the matters needing attention
1, computer, the control part of the power cord zero, fire cannot reverse connect, should strictly according to the original position with infixing. If any peripherals, connection is finished, whether should test front-housing charged.
2, mobile computers control equipment, electricity shall, before the first check connection lines, panel without loosing phenomenon.
3, cannot optional change communication lines, flat connection lines, the position of length.
4, mobile if found short circuit, tripping, burning up the line, smoke abnormal manifestation, should not be repeated electrify test, it shall promptly troubleshooting.
Three software operating matters need attention
1, software backup: WIN2003, WINXP, applications, software installation procedures, database etc.
Suggest using "YiJianHaiYuan" software, easy to operate.
2, mastering installation method and original data recovery, backup.
3, master control parameter setting, basic data preset modification
4, skilled in the use process, operation and editing.
5, regular check virus, remove extraneous data
6, FeiZhuanZhi personnel, do not operating software system

没有评论:

发表评论